| Your personal background. |
|---|
Grid degas: 6.3 to 7.5 V at approximately 10 A. - Collector
voltage: -20 to -50 VDC with respect to grid. For the purposes of this description, we assume that the controller
is compatible with the typical Bayard-Alpert ion gauge sensor
such as the Lesker G075TN which has the following specs:
- Filament voltage: 3 to 5 VAC. Here is a general procedure
for checking out an ion gauge controller without an ion gauge sensor or vacuum system,
or the gadget described in the next section. The team at Maple Leaf is well
aware of all the struggles you may go through in the
kitchen when your Amana over is out of order.
Nothing coming out of it smells clean. Most common problems encountered with refrigerators are leaking water, ice
build up, noises coming from your refrigerator, and not cooling at
all. However, ion gauge controllers are readily available surplus for a small fraction of their new cost.
Interlock circuits: These provide protection for the ion gauge filament from high pressure and the electronics from external short circuits or other faults.
The ion gauge controller typically provides one or more "process control" outputs to switch other equipment based
on the measured pressure (not shown). Some ion gauge tubes have two or more filaments
so that if one burns out, another can be used in its place.
Before buying any one of these appliances we should search different brands and select
the best between them. From Business: All Appliance Repair Brands the technicians service in Worth:
Refrigerator Repair, Washer Repair, Dryer Repair, Dishwasher RepairAmana
Repair, Bosch Repair,… If water is dripping from the
bottom or sides of your dishwasher door, your door seal is most likely no longer functioning
properly and needs to be replaced. Eventually, you are going to have to cave in and realize these appliance need a little assistance before they
are going to start functioning properly again. Of
course, it is important for you to select the
right oven and appliance repair firm when you are faced with a broken machine.
With a warranty, you usually get a temporary replacement right away.
Especially when you buy the luxury seal on appliances, you need to know that they are kept well and by the right company.
The actual voltages found on the various pins as well as emission current range will depend on the design of the
controller. I don't know if there is any
benefit to electron bombardment degas but it is certainly more
complex and much more dangerous (with 800 V at sizable current availability) present on the ion gauge tube electrodes as well as the electrometer input during degas.
Typical requirements: 8 V at 10 A. Electron bombardment (less
common): An alternative technique applies a higher voltage difference than used when measuring
pressure (up to 800 V peak compared to around 150 VDC) between the filament
and grid (which is shorted to the collector), resulting
in a current flow of up to 150 mA or more. 180 VDC at up to the maximum emission current
of 0.5 to 2.5 mA, some up to 10 mA or more. 150 VDC with respect to grid.
Electrons attracted to the grid collide with and ionize some
percentage of the residual gas molecules in their path.
Grid bias supply: Regulated voltage to attract electrons from the filament.
The required ion gauge controller subsystems include: Filament power supply: Filament current is precisely regulated based on desired electron emission current.
Power up the controller with nothing attached and make sure it doesn't do anything
terrible. If homeowners wish to guard themselves from any sort of legal suits which may arise if the company's worker may
get injured while offering his service in your home, then make sure that the specific air conditioning company is insured.
Veneer is a thin layer of wood bonded to a heavier surface of a lesser-quality wood to make it look
like cherry, for instance, or walnut. Metal Studs Vs.
Wood Studs: Which To Choose? Thus, for a full
scale reading of 10-7 Torr, the amplifier must have a full scale sensitivity of 1 nA!
Electrometer amplifier: This is a high sensitivity amplifier
range selectable between 10-3 and 10-7 Torr full scale (give or
take a an decade or two). Of course, these ion gauge tubes can't be run at 1 Torr but the ion current scales linearly with pressure.
But basically, it means that at a pressure of 1 Torr, the ion current would be S times
the electron current. Degas power supply: Some means
is provided to heat the grid and collector to drive
off gases that may have contaminated their surfaces when the system
was at high pressure or up to air.
Also visit my homepage "http://camillacastro.us/forums/profile.php?id=18379 |
| Your feedback on this profile |
|---|
| Recommend this profile for User of the Day: |
I like this profile |
| Alert administrators to an offensive profile: |
I do not like this profile |
|
| Account data |
View |
| Team |
None |
|